Introduction
- Huawei E303 For Mac Windows 10
- Huawei E303 Mac Os
- Huawei E303 For Mac
- Huawei E303 For Mac Os
- Huawei E303 For Macbook
Some Huawei USB modems, such as the E303 and E353, support an easy-to-use HiLink mode. This mode allows you to perform basic modem configuration via a web interface instead of the command line.
Huawei E303 For Mac Windows 10
HiLink mode is more limited than the standard PPP configuration–notably, you cannot establish inbound connections to the device. Still, it may be useful for some simple applications if your modem supports it.
Windows and MacOS
Slide the cover off of the Huawei E303 Modem and insert your Hologram SIM card with the full-size SIM insert.
Traktor Pro free. download full Version Mac Crack Stellarium 1.5 Free Download For Android Ipcc Cost Accounting Notes Pdf. HUAWEI E303 Huawei e303 driver Huawei e303 firmware update HUAWEI E303 HiLink Huawei e303 linux Huawei e303 modem unlocker Huawei e303 review Huawei e303 specification Huawei e303 unlock Huawei e303 usb modem HUAWEI.
- USB 3.0 WiFi Adapter AC1300Mbps for PC, Wireless Network Adapter Dual Band 5GHz 2.4GHz for Mac OS 10.6-10.15,Windows XP,10,8.1,7,Vista 4.4 out of 5 stars 451 $24.99.
- Huawei hilink e303 free download - HUAWEI HiLink (Mobile WiFi), Huawei HiLink (Mobile WiFi), HuwiManage for Windows 10, and many more programs.
- Thank you so much, Jide, I was desperate to get my Huawei E303 rnnning again after upgrading to 10.11. This worked perfectly smooth.
Plug the modem into your computer. The modem will mount itself as a storage device with the appropriate drivers on it. Install the drivers from the device, or download and install the latest drivers from the Downloads section of the E303 product page.Click Settings->Profile Management->New and add a profile for the Hologram APN (
hologram
) as shown here:Save your changes and then go to the Connection Settings page. Enable the auto connect options as shown here:
- When the install finishes, a web browser should automatically open to the Huawei HiLink settings page. If this doesn’t happen, navigate to 192.168.1.1.
- Click back to the Home page and click the connect button. You should now be connected to the internet via cellular.
Linux
Install the usb-modeswitch utility, which will handle switching the modem from storage mode to modem mode. For Debian-based distributions (e.g. Ubuntu and Raspbian), install this package from the standard repositories with:
Then reboot your PC.Slide the cover off of the Huawei E303 Modem and insert your Hologram SIM card with the full-size SIM insert.
Huawei E303 Mac Os
Then plug the modem into a USB port on your PC.Run
ifconfig
to find the eth*
device corresponding to the modem. If you are unsure which eth
device is the right one, you can unplug the modem and see which one disappears when running ifconfig
again.If the network interface doesn’t have an IP address assigned (no inet addr entry in
ifconfig
), run the DHCP client to acquire an address:Where
eth1
should be replaced with the modem’s device name.Open a web browser to 192.168.1.1 to configure the modem via web UI. Set up the Hologram APN profile and connection settings as described in the Windows/Mac instructions above, then click the Connect button on the device home page.Disable or unplug your PC’s other network connections (ethernet or wireless), then test your internet connection:If you get an error, you may need to add a route configuration so that network traffic is routed to the new cellular interface. From the command line, enter:
![Huawei E303 For Mac Huawei E303 For Mac](/uploads/1/1/8/7/118772709/276761428.jpg)
Where
eth1
should be replaced with the modem’s device name. Then retry the ping
.To automatically enable the modem whenever it’s plugged in and across restarts, you’ll need to update the networking config. In Debian-based distributions, add the following lines at the end of the file
/etc/network/interfaces
:Where
Read moreeth1
should be replaced with the modem’s device name.Credits
benstr ?
Connecting the world with Soracom.io and AWS.
Hello,
Huawei E303 For Mac
I have updated to the latest OS X El Capitan, v. 10.11. Since that time my Huawei E303 USB modem is not working anymore (it worked fine with previous OS X, v.10.10). I receive this message: 'Default configuration does not exist'. But it does exist in modem settings, however, it doesn't show up in profile name anymore so that I can choose it and connect to the internet. I'm without internet now - thanks El Capitan ?
My system is: iMac late 2013 with OS X El Capitan, processor 3.5 GHz Intel Core i7, Memory 16GB, Storage 3.11TB. Please help me to solve this issue. Thank you.
Huawei E303 For Mac Os
iMac (27-inch, Late 2013), OS X El Capitan (10.11), null
Huawei E303 For Macbook
Posted on